Doorway / InSite Code

Label

Description

Units

Default Value

Range

C1

MNFA

Minimum Fresh Air

%

10

0 to 100

C2

NOWS

Minimum Wind Speed for Wind Direction Indication to be valid

m/sec

1

0 to 25

C3

MXWS

Maximum Wind Speed (Window Shut)

m/sec

0

0 to 25

C4

MNWS

Minimum Wind Speed (Window open)

m/sec

0

0 to 15

C5

WNWD

Window Direction

Degrees

0

0 to 360

C6

DDEV

Wind Direction Deviation, the deviation in Wind Direction from dead down wind when the Window will be forced shut.

Degrees

0

0 to 360

C7

INMD

Input Mode use of terminals 'input a' :
0: additional temperature input for max,min,average use SACT
1: external input (short = occupied) AND internal occ
2: external input OR internal occ
3: external input signal only
4: Alarm input
5: Alarm if input does not match Pump/Fan State
Note modes 2 & 3 are only suitable for use with Actuator in Control Mode 2, small plant driver mode.

-

0

0 to 5

C8

MIND

Minimum demand, used for defining Occupancy switching for the Fan/Pump:
0: will run pump/fan throughout Occupancy
>0: will require minimum demand level before pump/fan will run

-

4

0 to 10

C9

OCCO

When set controller will only run during the occupied period

-

0

0 to 1

C10

HPRD

Heating valve period or minimum on time

secs/10

Depends on type

1 to 60

C11

HDLY

Interlock delay:
negative value delays fan (or pump) after heating starts
positive value cause run on of fan after heating shuts down

mins

0

-30 to 30

C12

CPRD

Cooling valve period or minimum on time

secs/10

Depends on type

1 to 60

C13

CDLY

Interlock delay:
negative value delays fan (or pump) after cooling starts
positive value cause run on of fan after cooling shuts down

mins

0

-30 to 30

C14

FPRD

Fan period, minimum time to change fan speed steps (6R + 7R version only)

secs/10

12

1 to 60

C15

CALC

Calculation Mode:
0: Multiply the Factors
1: use Loweset Factor

-

0

0 to 1

C16

MANL

Manual level , from Doorway

%

0

-100 to 100

C17

CMDE

Control Mode:
0: driver only inputs used for monitoring or alarm
1: closed loop control, input b primary sensor
2: on/off control, heating or cooling demand will be 100% when controller is 'occupied'. Sensor inputs used for monitoring or alarm functions

-

0

0 to 2

C18

ALRM

Alarm mode:
0: ignore alarms
1: report alarms
2: report alarms, shut down all outputs on local alarm
3: report alarms, shut down all outputs on STOP alarm or local alarm
4: report alarms, shut down all outputs on STOP alarm only

-

0

0 to 4

C19

ALST

Sets alarm state

-

0

0 to 1

C20

MXVA

Maximum Voltage output a (for AOP types only)

V

10

0 to 10

C21

MNVA

Minimum Voltage output a (for AOP types only)

V

0

0 to 10

C22

MXVB

Maximum Voltage output b (for AOP types only)

V

10

0 to 10

C23

MNVB

Minimum Voltage output b (for AOP types only)

V

0

0 to 10

Doorway / InSite Code

Label

Description

Units

Default Value

Range

I1 (C30)

FRST

Frost Protection Mode (SPNO violated)

-

-

0 to 1

I2 (C31)

OCCD

Occupied

-

-

0 to 1

I3 (C32)

WMUP

Not used in this version

-

-

0 to 1

I4 (C33)

EXIP

External Input State

-

-

0 to 1

I5 (C34)

COOL

Cooling mode

-

-

0 to 1

I6 (C35)

RLYA

Triac A Status (3T versions only)

-

-

0 to 1

I7 (C36)

RLYB

Triac B Status (3T versions only)

-

-

0 to 1

I8 (C37)

RLYC

Triac C Status (3T versions only)

-

-

0 to 1

W1 (C38)

AUTO

Automatic/Manual Status

-

-

0 to 1

W2 (C39)

OVRD

Override

-

-

0 to 1

W5 (C42)

HAND

Manual Hand; use with MANL to set output level

-

0

0 to 1

W6 (C43)

POT

Selects whether the board mounted potentiometer option is fitted or not

-

0

0 to 1

W7 (C44)

SERV

Service Pin Msg (to Doorway +InSite, self resetting)

-

-

0 to 1

S1* (C50)

TEMP

Measured temperature

Deg C

-

0 to 95

S2* (C51)

HCOP

Heat cool output to drivers (cooling negative)

%

-

-100 to 100

S3 (C52)

REQD

Current setpoint

Deg C

-

5 to 90

S4 (C53)

HDMD

Heat demand from loop or from Zone Controller

%

-

0 to 100

S5 (C54)

CDMD

Cool demand from loop or from Zone Controller

%

-

0 to 100

S6 (C55)

FDMD

Fan demand

%

-

0 to 100

S7 (C56)

OSFR

Outside Temperature Override Factor

%

-

0 to 100

S8 (C57)

WSFR

Wind Speed Override Factor

%

-

0 to 100

S9 (C58)

WDFR

Wind Direction Override Factor

%

-

0 to 100

S10 (C59)

FACT

Overall Override Factor

%

-

0 to 100

K1 (C60)

MXWS

Maximum Wind Speed, speed at which Window is Overriden shut

m/sec

0

0 to 25

K2 (C61)

MNWS

Minimum Wind Speed, speed at which window is still allowed to be 100% open

m/sec

0

0 to 25

K3 (C62)

Reserved for supervised setpoint from master controller

-

-

-

K4 (C63)

WNWD

Window Direction, compass bearing looking directly out of the window

Degrees

0

0 to 360

K5 (C64)

DDEV

Wind Direction deviation, deviation from dead down wind where window must be shut

Degrees

0

0 to 160

K6 (C65)

NOWS

No Wind, below this Wind Speed the Wind Direction is ignored

m/sec

1

0 to 25

K7 (C66)

MNFA

Minimum Fresh Air setting for the Window opening

%

10

0 to 100

K8 (C67)

OUTT

Outside Temperature Top limit, at which the window can be fully open

Deg C

0

0 to 25

K9 (C68)

OUTB

Outside Temperature Bottom limit, at or below which the window will be shut

Deg C

0

0 to 25

Engineering Parameters; only accessible via Doorway and InSite

C180

DI A

Input 3-4 digital status

-

-

0 or 1

C181

DI B

Input 5-6 digital status

-

-

0 or 1

* 24 hour plots available for these values by default

Plotting interval and plotted variable changeable via Doorway or InSite